Producer: Ce Heinke
Type: Put in
Estimated DOM: 1925
Total length: 12.99"
Blade: steel, 6.29", 1 sharp side
Inscription: C.E. HEINKE : LONDON on handle.
Sheath: solid brass
Handle: solid brass
Remarks: Photo courtesy: Diving Museum Lemmer, The Netherlands. The age of the knife can be determined by the inscription. Who knows more about this?

 

Producer: Ce Heinke
Type: Push in
Estimated DOM: 1936
Total length: 12 1/2 inches
Blade: Stainless Steel length 6 1/2inches 1 sharp edge
Inscription: none
Sheath: Solid Brass
Handle: Solid Brass
Remarks: The company name has changed from the previous knife to & Co

 


Photo courtesy of Dr Mike Burchett

Producer: CE HEINKE & Co Ltd. LONDON
Type: Push in with spring grip
Estimated DOM: 1922-1960
Weight: Knife 650 gms : Sheath 730 gms
Total length: 280 mm (11 inches)
Blade: Carbon steel ; length 160 mm (6.26 inches) X 38 mm (1.5 inches) wide edges straight with sharp bottom edge and top edge fully serrated (10 teeth per inch)
Inscription: None
Sheath: Solid brass, inscribed on outside in relief: HEINKE LONDON. Brown leather strap (one inch wide) is held in place on inside of sheath by two copper rivets.
Handle: Solid brass with an inscription machine stamped on right hand side : C E HEINKE & Co Ltd.
Remarks: Last in series of the standard brass Heinke knives. A non serrated version was also available with both edges straight and sharp.

 

Producer: Ce Heinke
Type: Push in
Estimated DOM: 1960
Total length: 11 inches
Blade: Stainless Steel 6inches long 1 sharp serrated edge
Inscription: On Blade -Heinke London,on handle- Heinke underwater swimming products
Sheath: Die-cast aluminium
Handle: Black Rubber
Remarks: Known as Dagger or stiletto, Also available with steel blade cost new 1961 £2 11s 3d

 

Producer: Ce Heinke
Type: Push in
Estimated DOM: 1965
Total length: 11 inches
Blade: Stainless steel, 6 inches 1 sharp edge 1 seratated edge
Inscription: On handle-Siebe Heinke/Underwater swimming knife.On blade-Siebe Heinke of London
Sheath: Die-cast aluminium
Handle: Black Rubber
Remarks: Almost identical to previous knife by now Siebe and JHeinke products have merged. Handle on this model is riveted to gether in Heinke model it is screwed to gether

 

Producer: Siebe Heinke
Type: Push in
Estimated DOM: 1945
Total length: 10 inches
Blade: Stainless steel 6 inches, 1 edge sharp 1 edge serrated
Inscription: On blade-Siebe-Heinke Chessington England Underwater knife.
Sheath: Leather (not shown)
Handle: Cork
Remarks: Similar in design to the Typhoon floating dagger.

 



 

Producer: William Rodgers
Type: Push in
Estimated DOM: 1960
Total length: 12 inches
Blade: Stainless steel 6 inches 1 edge sharp 1 edge serrated
Inscription: I cut my way AMPHIBIAN William Rodgers Made in Sheffield England Stainless.
Sheath: Leather (not shown)
Handle: Cork
Remarks: Similar in design to Milbro floating knife

 

   

Producer: Siebe & Gorman & Co.
Type: Screw-in
Estimated DOM: Circa 1900
Total length: 12 inches
Blade: Steel 6 inches 2 sides sharp
Inscription: Siebe & Gorman on sheath
Sheath: Solid Brass
Handle: Rosewood
Remarks: Photo Courtesy of Stefan Samojauska

 

Producer: Siebe Gorman & Co
Type: Put in
Estimated DOM: Circa 1910
Total Dimensions: 12 inches
Blade: Steel 2 sharp sides
Inscription on blade: Siebe Gorman & Co
Sheath: Solid Brass
Handle: Walnut
Remarks: Photographed along side a usual SG Knife notice it's much shorter and narrower. This is the next model after the Screw in knife in the previous picture.

 

Producer: Siebe, Gorman & Co.
Type: Push in
Estimated DOM: 1930's
Total length: 12 inches (305 mm)
Blade: 2 sharp sides
Inscription: Siebe Gorman & Co *
Sheath: Brass
Handle: Light Walnut
Remarks: * This asterisk on the blade sgnifies the blade in anti-magnetic

 

Producer: Siebe, Gorman & Co.
Type: Put in
Estimated DOM: 1950
Total length: 13.77"
Blade: stainless steel, 7.68", 2 sharp sides
Inscription: SIEBE . GORMAN & Co on blade
Sheath: solid brass
Handle: brown color bakelite with brass pieces
Remarks: Also produced with one sharp and one serrated side

 

Producer: Siebe, Gorman & Co.
Type: Push in
Estimated DOM: 1920
Total length: 13 inches
Blade: Steel 2 sides sharp
Inscription: Siebe Gorman& Co
Sheath: Leather with copper roves and catgut stitching
Handle: Very dark brown , almost black ebonite
Remarks: Almost certainly not a factory made sheath , possibly a Diver's tender's knife

 

Producer: Siebe, Gorman & Co.
Type: Put in
Estimated DOM: 1950
Total length: 13.77"
Blade: stainless steel, 7.68", 2 sharp sides
Inscription: SIEBE GORMAN & Co * on blade
Sheath: solid brass
Handle: brown color bakelite with brass pieces
Remarks: Photo courtesy: De Helmduiker. This is the "anti magnetic type", recognisable by the * behind the name on the blade. Also produced with one sharp and one serrated side.

 

Producer: Siebe, Gorman & Co.
Type: Put in
Estimated DOM: 1960
Total length: 13.77"
Blade: steel, 7.68" 2 sharp sides
Inscription: SIEBE GORMAN on blade
Sheath: solid brass
Handle: black color bakelite with chromed brass pieces
Remarks:  Also produced with one sharp and one serrated side

 

 

Producer: Siebe Gorman
Type: Push in
Estimated DOM: 1960
Total length: 13.77 inches
Blade: Steel 7.68 inches , 2 sharp sides
Inscription: SIEBE GORMAN & Co * on blade
Sheath: Solid Brass
Handle: Black coloured bakelite with self colour brass parts.
Remarks: As the knife above but the handle parts have not been chromed. Photo courtesy of J Hasselbach. Please refer to note at the foot of this page for further information.

 

 

Producer: Siebe, Gorman
Type: Push in
Estimated DOM: 1945
Total length: 13 inches
Blade: Steel 2 sharp sides
Inscription: none
Sheath: Tinned Brass
Handle: Ebonite
Remarks: An unusual tinned sheath but also a rare hexagonal nut at the end of the pommel.

 

 
Photo courtesy of Dr Mike Burchett.

Producer: Siebe Gorman & Co Ltd (unconfirmed)
Type: Push in with spring grip
Estimated DOM: circa 1960
Weight: Knife 450 gms , sheath 480 gms
Total length: 339 mm (13.3 inches)
Blade: Steel (non magnetic) ;length 196mm (7.7inches) X 34 mm (1.38 inches) wide. Edges straight, one sharp and the other fully serrated with forward serrations (7tpi)
Inscription: Lightly electro-etched onto blade is: AP 62 60 NON-MAGNETIC
Sheath: Polished solid brass, stamped NON-MAGNETIC A.P. 6261 on both sides.
Handle: Dense black plastic with brass cross-guard , ferrule and tang nut
Remarks: The blade does not appear to have the edge quality of other Siebe Gorman knives. There is a characteristic raised centre 'V' of the blade where it meets the cross-guard. There may also be circular punch marks on the end of the brass tang nut.

 

 
Photo courtesy of John Wilkins.

Producer: Siebe Gorman
Type: Push in
Estimated DOM: After 1957
Total length: 13.5 inches
Blade: Non-Magnetic stainless steel 1 sharp side 1 serrated side
Inscription on blade: AP6260 NON-MAGNETIC
Inscription on Sheath: AP6261 NON-MAGNETIC
Sheath: Solid Brass
Handle: Black Bakelite
Remarks: Siebe Gorman non-magnetic diver's knifefirst issued in 1957. For Navy stores purposes value £72 in 1983

 


Photo's courtesy of John Wilkins.

Producer: Siebe Gorman & Co.
Type: Push in
Estimated DOM: 1970
Total length: 13.75 inches
Blade: Non magnetic stainless steel 1 sharp side 1 serrated side
Inscription on blade: 0433.431.7338 NON-MAGNETIC
Inscription on Sheath: None
Sheath: Solid Brass
Handle: Black Bakelite
Remarks: The numbers etched to the blade are the Royal Navy's store's part number.

 

 

Producer: Siebe, Gorman
Type: Push in
Estimated DOM: 1955
Total length: 13 1/2 inches
Blade: 8 inches stainless steel 1 side sharp 1side serrated
Inscription on blade: SIEBE GORMAN & CO * on sheath NON MAGNETIC
Sheath: Brass
Handle: Walnut
Remarks: Anti magnetic knife issued to mine clearance divers of the Royal Navy

 

Producer: Siebe, Gorman & Co.
Type: Put in
Estimated DOM: 1965
Total length: 13.77"
Blade: steel, 7.68", 1sharp and 1 serrated side
Inscription: SIEBE GORMAN on blade
Sheath: solid brass
Handle: brown wood with brass pieces
Remarks: Photo courtesy: Diving Museum Lemmer, The Netherlands. Also produced with two sharp sides

 

Producer: Siebe, Gorman & Co.
Type: Put in
Estimated DOM: n.a
Total length: 13.77"
Blade: steel, 2 sharp sides
Inscription: none
Sheath: solid brass
Handle: black color bakelite with brass pieces
Remarks: Photo courtesy: Diving Museum Lemmer, The Netherlands. A very rare knife! Look at the typical shape of blade and handle. Who can tell us more about it ? 

 

Producer: Siebe Gorman
Type: Put in
Estimated DOM: 1935
Total length: 13 1/2 inches
Blade: Steel 7 1/2 inches 2 edges sharp
Inscription: Siebe Gorman Co
Sheath: Solid brass
Handle: Maple
Remarks: Unusual to see this type of light wood handle.

 

 

Producer: Siebe-Heinke
Type: Push in
Estimated DOM: 1956
Total length: 13 1/2 inches
Blade: stainless steel 7 3/4 inches 2 sharp
Inscription: On blade-Siebe-Heinke of England on edges.
Sheath: Solid Brass
Handle: Black Bakelite
Remarks: none 

 


Photo courtesy of Dr Mike Burchett

Producer: Typhoon International Ltd.
Reference name: Typhoon Pic Knife
Type: Put in
Estimated DOM: circa 1970
Total length: 320 mm (12.5 inches)
Blade: Bowie style, stainless steel, 185mm (7.25inches) long with serrated lower edge.
Inscription: Maker's logo on blade left side, stamped ruler markings on right side.
Sheath: Black plastic with company logo.
Handle: Hard black rubber with hammer-shaped pommel.
Remarks: Knife history ...the knife was an interim measure (1970-1972), used by the Royal Navy between the phasing out of the Typhoon assembled 'Taylor's Eye Witness' knife and the introduction of the standard Hopkinson/Nowill design. There are no naval issue marks as this was a civilian
knife used by the Forces. The recent version has an updated logo and name tag..

 


Photo courtesy of Dr Mike Burchett

Producer: Hopkinson.
Type: Put in
Estimated DOM: circa 1970
Total length of knife: 330 mm (13 inches)
Blade: Steel, length 195 mm (7.7 inches) edges straight with one side sharp and one serrated.
Inscription: Non on blade, 'H' symbol and NS number on hilt. NSN on sheath.
Sheath: Synthetic black plastic.
Handle: Black rubber with steel pommel.
Remarks: Photo courtesy: Knife history. This knife design was manufactured by Hopkinson's (see photo) under both the Hopkinson's name and the John Nowill name (see the next knife below). The knife is still made by Divex who also make a non-magnetic version with a beta-titanium blade. A non-magnetic version was also made by Nowill & Sons. The knife was first produced in the early 70s and is still current issue in the Royal Navy today. N-S numbers are as follows: on blade or hilt 4220-99-523-9744;sheath 4220-99-523-9745 and straps 4220 -99-523-9746.Some variations include 1) no markings on the knife or sheath .2) maker's name and NSN etched on blade with NSN in relief on sheath (before 1979) and 3) NSN is on rubber hilt instead of blade (1979 onwards).

 

Producer: John Knowill & Sons Ltd.
Type: Put in
Estimated DOM: 1970
Total length: 13.77"
Blade: anti magnetic steel,  7.87", 1sharp side, 1 serrated side
Inscription: NATO stock number on sheath
Sheath: synthetic material
Handle: black color synthetic material with chrome piece
Remarks: Photo courtesy: Diving Museum Lemmer, The Netherlands. British navy knife, used in combination with the CDBA diving apparatus. 

 

 
Photo courtesy of Mike Burchett and Robert Burchett.

Producer: John Nowill & Sons Ltd. (parent company J. Adams ‘Sheffield Knives’).
Type: Put in.
Estimated DOM: Circa 2005 and is current issue in 2010.
Total length: 330mm (13 inches).
Blade: Non-magnetic, beta-titanium ‘dagger’ form. Length 195mm (7-5/8 inches). One plain sharp and one serrated edge (22 teeth, about 4 tpi). Knife weight, 292 grams nominal.
Inscription: Etched “D * (with ‘crossed keys symbol’)”. Underneath is maker’s name “John Nowill & Sons LTD. SHEFFIELD ENGLAND”.
Sheath: Synthetic black plastic type of commercial design that carries an “ETERNAL TRADE MARK” logo. Sheath is supplied with low magnetic rubber straps and plastic ‘cam-lock’ buckles (designated N.S.N. “4220-99-770-1074”).
Handle: Dense black rubber, with round titanium butt-knob sunk into pommel. There is no Nato stock number on the grip.
Remarks:  This non-magnetic knife is supplied by J.Adams Ltd. to Divex who are the MOD suppliers. Some of the early (2005) titanium knives may carry the Divex name instead of the maker’s name. The knife has designated NSN: “4420-99-096-4501” for military ordering purposes. A civilian version has been observed without knife inscriptions. The Admiralty may issue the knives with the older style, military diver’s scabbard.

 

Producer: Life Support
Type: Put in
Estimated DOM: 1970
Total length: 12.20"
Blade: anti magnetic phosfor bronze,  7", 1 sharp side, 1 serrated side
Inscription: none
Sheath: Rubber
Handle: Black Rubber
Remarks: Photo courtesy: Diving Museum Lemmer, The Netherlands. British navy knife.

 

 
Photo courtesy of Warren Hastings.

Producer: Typhoon International Limited
Type: Put in
Estimated DOM: 1962-1970
Total length: 9 1/4 inches (23 cm)
Blade: Stainless steel 4 1/2 inches 1 side sharp 1 side serrated.
Inscription: Taylor's Eye Witness Stainless Steel Sheffield.
Sheath: Rubber
Handle: Black Rubber
Remarks: This knife was originally made for divers but was found to be lightweight in service and was not popular. It was however issued to ships and clearance divers as well as Special Boat Service members. The blade was made by Taylor's Eye Witness Limited and supplied to Typhoon International Limited. The Taylor's blade knife is AP no 0433/1546 and the wholly Typhoon knife which was a NATO pattern 0433-924-8626. Another variation of this knife exists with a shackle slot in the blade.

 

 
Photo courtesy of Mike Burchett and Robert Burchett.

Producer: “technisub” (established in 1962 by Luigi Ferraro of Italy).
Type: Put in.
Estimated DOM: Circa 1990s (with given year etched on blade).
Total length: 320mm (12-1/2 inches).
Blade: Stainless steel (marked on ricasso); heavy duty bowie-style. Blade is double-edged (197mm in length), with a plain sharpened lower edge and partially serrated upper edge.
Inscription: Etched military marking “MDE ↑ 93” with NATO stock number “4220 99 925 2814” above.
Sheath: Synthetic black plastic military style which carries the “technisub” trade mark on the front. Sheath is supplied with retaining loop, rubber straps and plastic buckles.
Handle: Dense black plastic, marked “AQUALUNG” in relief (inverted) on both sides. A round steel butt-knob is screwed into the pommel.
Remarks:  This knife was issued to British army divers during the 1990s.

 

 
Photos courtesy of Mike Burchett & Robert Burchett.

Producer: Air Liquide (La Spirotechnique: “aqua-lung”).
Type: Put in.
Estimated DOM: Circa 2000 onwards.
Total length: 320mm (12-1/2 inches).
Blade: ‘STAINLESS STEEL MADE IN JAPAN’ (marked on ricasso); heavy duty bowie-style. Blade is double-edged (197mm in length), with plain sharpened lower edge and partially serrated upper edge.
Inscription: Ricasso stamped “aqua-lung” trade mark and 6 inch rule on one side of blade.
Sheath: Synthetic black plastic type that carry's the “aqualung” trade mark on the front. Sheath is supplied with a retaining loop, rubber straps and metal buckles.
Handle: Dense black rubber and marked “NAVY KNIFE” in heavy relief on both sides. A round, knurled steel butt-knob is screwed into the pommel.
Remarks:  This knife is a likely replacement for the earlier “technisub” Aqualung military knife. This knife model is known as ‘No.7015 Navy Knife’. The knife is British NATO stock coded as “Knife & Sheath (Divers)” and its National Stock Number (NSN) is listed as ‘4220-99-523-2814’. It is not known precisely when this general purpose diver’s knife was first introduced, or if it is in current use.

Research suggests the Royal Navy diver's knife of a similar design was in used since before 1914. Navy regulations stated all divers and attendants must carry a knife The knives were generally carried on a frog or small loop of leather which hung from the divers belt, however some of the more specialised groups of Navy divers carried the knives in their boot as the Charioteers would. The sheath was not stamped with the maker's name whereas the blade of the knife was stamped. A similar pattern of knife was the Non-magnetic knife used by clearance divers . Both the knife and the sheath was stamped Non- Magnetic.